----------------------------------------------------------------------
【Voltage Compatibility】
When using electrical appliances, please note that they are designed for Japanese voltage specifications (90-110V), so if you use them with a different voltage, it may cause a malfunction.
【Plug Type】
Our products use Japanese plug types (A or B type).
Please use a conversion adapter if necessary.
【Important Note on Transformers and Adapters】
A transformer adjusts voltage to match your device’s requirements.
A conversion adapter only changes the plug shape and does not adjust voltage.
Using only a conversion adapter without a transformer may result in damage to the product.
【Liability】
We are not responsible for malfunctions or damages caused by improper use, such as operating the product without a transformer.
----------------------------------------------------------------------
[Hall Joystick and Additional Sensors] - 4x Hall effect stick replacement for PS4, PS5, Xbox, and most third party controllers (ALPS, FU, etc.) that have regular analog or hall control sticks inside. Reassemble the stick assembly with 8x additional sensors and magnets to fit your specific controller. A dedicated Vcc tester will distinguish which pins are Vcc/Gnd. (🔺Note: Make sure your controller comes with a regular ✅ UniA stick.)
[Heating Plate Included] – The copper heating plate melts all the solder joints with the soldering iron at the same time. Tin the wire, cut it to a sharp point, stick the tip into a small hole, and suck the solder into the small hole. Multi-gauge braided wire performs better than solder wick. PCB clamps help support the PCB on your workbench. 🔺Attention: Do not place the clamp near hot joysticks. It will melt.
[Calibration Strategy] – You can adjust the center with the included tool. The outer range of these hole sticks is slightly wider than analog sticks. Although mentioned in the installation guide, we do not recommend calibrating the outer ranges with the Calibration app. You can manually increase or decrease the outer range using 8% O-rings or Teflon tape. (🔺Note: For more control over calibration, please refer to another series of kits with MCU PCB.)
[Compatibility and Notes] – 1. 🔺Please check the images and descriptions for compatible/incompatible sticks and controllers. 2. 🔺External magnets may interfere with the Hall stick, such as the LT bumper button on Xbox layout controllers. If this concerns you, please do not purchase. For a kit with MCU control for Xbox, please visit B0CYBWQWTB. 3. 🔺You will need some serious soldering skills and devices to unsolder the old stick from the PCB.
[HL-FU Box Contents] – 4 x Hall Joysticks, 8 x Additional Hall Sensors and Magnets, 1 x Vcc Tester, 1 x Heating Plate, 1 x Center Adjustment Wrench, 1 x 8% O-ring, 1 x Teflon Tape . (🔺 Make sure your soldering iron is 60 watts or higher and has a large tip. Controller, disassembly screwdriver tool, soldering iron, and other soldering tools and materials are required and not included.)
4x Hall Effect Joysticks with Adjustable Center Structure
8x Additional Hall Sensors for Different Vcc/Gnd Layout
A Dedicated Vcc Tester distinguishes Vcc/Gnd Pads on PCB
A Heating Plate helps to Desolder the old Sticks off PCB
8% O-ring and Teflon Tape for Outer Range Adjustment
Two More Choices:
1. Go to B09KVG7DGY for UniA series of Analog Stick by ALPS and FU
2. Go to B0CYBRZ2YP for hallstick series with calibration MCU PCB for fine calibration
✅Compatible Controller Example:
PS4/DS4, PS5/DS5, PS5 Edge/DSE
Some Raiiu, Razar, Scuf and most 3rd brand
Xbox One and Elite, Xbox Series S/X
(The LT bumper slightly interferes with left stick.)
🔺Incompatible Example – (Cause):
Switch Pro – (Power supply problem. Plz go to B0CYBLZPW1)
PDP Rematch 049 – (It uses a UniB stick.)
Xbox 360 – (It uses an X360 stick.)
Thunderobat G50S, Games-Sir G7 SE – (Totally different joystick used)
PS3 – (A special 4Pin stick used.)
Reminders:
1. This model is a replacement for most controllers with common type of ✅UniA control stick inside, Not for 🔺UniB or 🔺X360 type
2. We do not suggest calibrating its outer range with calibration App though we mentioned it on the user guide
3. External magnets may interfere with the hall stick, for example the LT bumper button of Xbox. Do not buy if you concern this, and take a view at B0CYBWQWTB for hallstick with MCU control
4. Teardown screwdriver tools, USB wired and wireless controllers, USB input and output charging cables Other soldering tools and materials are NOT included
