----------------------------------------------------------------------
【Cautions for using electrical products】
When using electrical appliances, please note that the voltage is different from that of Japan, which may cause malfunctions.
Since the plug type is Japan type(A or B type), please check the voltage and use a transformer.
Please note that a transformer is different from a conversion adapter.
We are not responsible for malfunctions caused by use without a transformer.
【Voltage Compatibility】
When using electrical appliances, please note that they are designed for Japanese voltage specifications (90-110V), so if you use them with a different voltage, it may cause a malfunction.
【Plug Type】
Our products use Japanese plug types (A or B type).
Please use a conversion adapter if necessary.
【Important Note on Transformers and Adapters】
A transformer adjusts voltage to match your device’s requirements.
A conversion adapter only changes the plug shape and does not adjust voltage.
Using only a conversion adapter without a transformer may result in damage to the product.
【Liability】
We are not responsible for malfunctions or damages caused by improper use, such as operating the product without a transformer.
----------------------------------------------------------------------
Japan's first "all-around" ring-emitting LED light, optimal balance, slim head all around, and comfortable operability. *For domestic rechargeable impact drivers. As of December 2022, according to Makita research. Visibility during work has been significantly improved. Approximately 2.5 times the brightness (compared to Makita's previous 18V model). Illuminance can be switched in 3 levels (strong/medium/weak). *For domestic rechargeable impact drivers. As of December 2022, according to Makita research. Can also be used as a work light. It can also be used as a simple light in "light mode".Lighting time is about 1 hour.
New trigger switch. Intuitive trigger shift operation is possible from low to high speeds.Grip part close to shaft center. The hand you hold is close to the head, making it easy to press the shaft core. Reduces cam-out. Offsets the battery to the rear. The center of gravity has been optimized to allow for well-balanced tightening in all directions.Also, interference with obstacles is reduced.The operation panel is located at the rear, making it easy to see and use. You can operate the mode and check the remaining battery capacity while holding it.
Bit runout is the "industry's smallest" and double ball bearings are used. Newly shaped bit sleeve. Ribs on the edges prevent damage even if the sleeve hits a component. *For domestic cordless impact drivers. According to Makita research, December 2022. Tilt angle of approximately 10.5°. Excellent corner driving performance reduces cam-out. Comfortable when working near walls. The most suitable mode can be selected according to the work. Mode memory function. By pressing two buttons at the same time, you can register one frequently used mode.Use the button at hand to switch between the "most recently used mode" and the "registered mode."
18V DC, sliding Li-ion battery specification. Battery and charger sold separately. Tightening capacity: Machine screws M4 to M8/Ordinary bolts M5 to M16/High strength bolts M5 to M14/Coarse thread 22 to 125mm. Maximum tightening torque: 180N・m. Rotation speed [revolutions/min]: Fastest 0-3,600/strong 0-3,200/medium 0-2,100/weak 0-1,100. Easy mode rotation speed [rotations/min]: Wood 0-1,800/Volt 0-3,600/Tex thin plate 0-2,900/Tex thick plate 0-3,600. Number of blows [times/min]: Fastest 0 to over 3,800 Medium 0 to 3,600 0 to under 2,600 0 to 1,100. Easy mode number of blows [times/min]: Wood 0 to 3,800/Volts 0 to 3,800/Tex thin plate Stops immediately after the blow starts/Tex thick plate 0 to 2,600. Work amount per charge (wood screws material lauan φ4.3 x 65 mm guideline): Approximately 960 pieces
Machine dimensions: length 111mm x width 81mm x height 234mm. Mass: 1.5kg (including battery)
