Seal for semicircular arch shower cabin door DK13 4mm 2x40cm

THIS AUCTION IS FOR A SET OF 2 DK13 SEMI-CIRCULAR SHOWER DOOR SEALS, SIZE 4MM, 40 CM LENGTH! 1 PIECE = 2 x 40 CM!!! Shower Seals. Shower seals protect the bathroom from leaks and water spilling out of the shower enclosure, ensuring cleanliness and safety, and minimizing the risk of slipping on wet surfaces. Above all, they protect against flooding and wetting floors and ceilings below, which can result in very high renovation costs. The main function of a shower seal is to retain water within the enclosure. When water begins to leak from the enclosure onto the bathroom floor, you should consider replacing the seals. This is a sign of a leak and should be replaced as soon as possible. It's also worth checking whether leaking water is caused by wear or damage to the shower threshold. Seals are made of PVC and have two parts: a hard and a soft one. The harder part slides over the glass, while the softer part acts as a seal fin that protects against leaks. Seal replacement depends on the degree of wear and tear and the individual use of the shower enclosure. Wear and tear can include deformation, detachment, tearing, cracking, leaking, or wetting. This can also be caused by changes in bathroom temperature, humidity, water, steam, or the presence of mold, limescale, or stubborn dirt. In such cases, you should purchase a new set of seals. Shower enclosure seals are divided into: Standard: These are standard seals. They help protect the vertical and horizontal parts of the enclosure. We'll seal the side walls and the bottom edge of the door. Magnetic seals are very similar to standard seals, but they are also equipped with a magnet, allowing them to close together, for example, when closing the shower door. Magnets help close the shower door. We offer magnetic strips for doors that close at 90°, 135°, and 180°. Acrylic thresholds are also worth mentioning here, as they protect the shower enclosure from leaks and overflowing. Features: durability, water and moisture resistance, chemical resistance, resistant to fungi and mold, very easy to install and remove, colorless, inconspicuous, do not spoil the appearance of the room, provide sealing, are resistant to UV radiation, and magnetic seals help close the shower enclosure door. How to choose the right seal: When choosing a seal for your shower enclosure, you should consider five aspects: the thickness of the glass, where it will be mounted (horizontal or vertical), the length of the blade, the type of seal (standard, magnetic, or self-adhesive), and whether it's a square or semicircular enclosure. Replacing the shower enclosure seal: Once you've chosen the right size for your shower enclosure, check that it will fit the glass thickness and that the seal isn't too long or too short. If it's too long, you can easily cut it to size. It can't be too short. If you want to replace the old seal with a new one, it's worth checking how the original seal was installed. Was it simply pushed on or glued with silicone? If silicone was used, remove it from the surface with a glass scraper. Any additional cover strips should also be removed. When removing the seal from the shower door, grasp it by one end and carefully pull it off, keeping it in one piece. This will make it easier to cut the new seal to the correct length later. Cut the new seal to the correct length using the one you just removed. Place two seals side by side, preferably on the floor, and mark the cut point on the new one with a marker. Then, cut off the excess section with a knife or a special seal cutting tool, ensuring a straight edge. Be careful not to break or crush the seal. Prepare the door before applying the seal by washing it with water until the glass is perfectly clean. Then rinse thoroughly and dry. If your shower enclosure is already prepared in this way, you can install the seal. Carefully insert the standard or magnetic seal using the special notch in the seal and check that it is properly installed. Once you have the self-adhesive seal, remove the protective tape and carefully apply the seal in the correct location. If the purchased seal doesn't fit after testing it at home, don't cut it; you can exchange it for another one or return it. It's also worth remembering that a seal brought from a cold place should be allowed to warm up for a while. This will make installation easier. Our website offers a wide selection of shower seals, and you're sure to find the right seal for your shower enclosure. When replacing seals, it's also worth paying attention to the shower threshold, which is also a common cause of leaks. If necessary, we also offer acrylic shower thresholds, which are transparent and virtually invisible. They also protect and secure your bathroom from overflows and water ingress beyond the shower area. Replacing the threshold along with the bottom seal will provide excellent protection against cabin leaks. Note: Remember to regularly clean the seal to remove any deposits using bathroom cleaning fluids. This will extend the life of the strip.